cloudsjae.blogg.se -

#RS BA1 PORT FORWARDING INSTALL#
#RS BA1 PORT FORWARDING MOD#
#RS BA1 PORT FORWARDING SOFTWARE#

#RS BA1 PORT FORWARDING SOFTWARE#

While the software lacks some of the features found on the radio itself, the software does what it was designed to do.allow remote access to the majority functions of the radio.

This procedure always puts the rig back in the state it was before the remote session at my QTH.” – Julio, W4HY (Groups.I have the V2 version installed on several pc's, tablet,and laptop. You should then see a small window that indicates it is closing the remote utility. Then click the disconnect button at the bottom of the Icom Remote Utility window you should get a dialog box that asks if you want to disconnect the radio, click on YES and finally the X at the top right of that window. “Try this when you start to exit your remote session exit the RS-BA1 Remote Control window first by clicking the X in the top right of the window or the exit button on the top menu.

Having MONITOR enabled on the Icom 7610 will create an echo when transmitting using remote software.

Sometimes when I open it I don’t have to connect (power on) because the radio is already ON. That’s just because the radio is already powered ON.

Sometimes when I connect with the utility I get audio from the radio right away.

It just depends on how you shutdown the software. It should then go back to your normal setting MIC,USB or MIC,ACC.

#RS BA1 PORT FORWARDING MOD#

DATA OFF MOD will automatically change in the radio to LAN when we connect.

To use the Scope in RS-BA1 we need Unlink from setup properly in the radio.

It will switch ON automatically if it is OFF.

When we use RS-BA1 to connect to the radio we need CI-V Transceive ON in the radio.

For now it’s working and I get “good” audio reports on SSB.

Once I am more familiar with RS-BA1 I’ll do another video and show how I fined tuned my software to transmit SSB, and CW. I have a tip in the video for setting the F1 key on the keyboard for TX/RX. With the “REMOTE” enabled you can control the radio. See pictures and video below.Ĭlick the Power On or Connect button in the RS-BA1 Remote Control. Have a look at the Remote Setting and the MOD Select. When setting up the Connect Set in RS-BA1, you can use LAN (thanks Jeff, W6FCC ) for the Connection instead of USB. This is in the video below.Īfter you are connected to the radio with the Icom Remote Utility program open the Icom Remote Control program. Just verify that you use the same virtual COM port # in the Remote Control as you have set in the Utility software. The COM port you select is a virtual port, so the # is not important. Open the Utility and click on the “Add” button to setup and connect to the sever. Scroll down on that page to find the RS-BA1 section.

#RS BA1 PORT FORWARDING INSTALL#

The Remote Utility software and the Remote Control software.Īfter installing those from the CD-ROM, go to the Icom website and install the latest update. Two software applications are installed off the CD-ROM. You’ll need to buy a CD-ROM with RS-BA1 software if you don’t already have it.

Icom 7610 RS-BA1 Utility and Remote Software See Icom 7610 Screen Captures and “Things to watch out for”. When powering off the radio, put it in Standby (For remote control). That’s not a big deal and doesn’t need to be changed if you don’t want to. I’ll bet a lot of Hams are using MIC, ACC and I use MIC,USB. Try to determine if it is necessary to change yours. There may be one or two things different from your radio configuration. In the video below you’ll see how I have my radio setup. More information can be found here: Icom 7610 Clock, Timers and Network. First, connect the Icom 7610 to your network with the ethernet port on the rear of the radio.